[Daekyung Tech] Flame retardant tester (vertical type)Quote inquiry_ CS@roasexpo.comManufactured in accordance with KS and UL standards as well as test methods for combustibility of automobile interior materials,electric wires, and plastic materials.TYPE : VERTICALBURNER : BUTSENGAS : BUTANEINNER MATERIAL : STS 304OUTER MATERIAL : SS41 COATINGIGNIT..

[Daekyung Tech] Low-temperature impact testerQuote inquiry_ CS@roasexpo.comThis tester is a device that can perform both low-temperature impact and winding tests.It is also used to test the reliability, durability, and lifespan of various samples such as mechanical parts, electrical, electronic, chemical, metal, and ceramics...

[Daekyung Tech] Oil resistance testerQuote inquiry_ CS@roasexpo.comThis tester is a device that inspects physical properties by heating a specimen while stirring it at a high temperature in oil.Since it consists of 4 test tubes, 4 samples can be measured at the same time...

 [Daekyung Tech] Ozone testerQuote inquiry_ CS@roasexpo.comIn order to measure the deterioration of vulcanized rubber due to ozone in the atmosphere,it is designed and manufactured for the purpose of investigating and, testing ozone resistance by exposing a test piece to air containing a low concentration of ozone, which is artificially genera..

[Daekyung Tech] Thermal shock testerQuote Contact_ cs@roasexpo.comThe purpose is to observe the deformation of the product or sample by rapidly changing the temperature,and the composition of the device is classified into a high-temperature and low-temperature preheating room and a room temperature room.TYPE : 3 ZONEINNER SIZE : ORDER MADETEST TE..

[Daekyung Tech] Thermal shock tester (2Zone)Quote Contact_ cs@roasexpo.comThis device is a tester to check whether there is any abnormality in the sample due to sudden temperature change by moving the sample to the hightemperature room and the freezing room within a short time.It is a device designed and manufactured so that temperature changes a..

[Daekyung Tech] MITQuote Contact_cs @roasexpo.comBy measuring the fluidity in the molten state of the resin, the physical properties (strength, flow chart) and, raw materials of the material are inspected, so defective products can be prevented in advance. is a device for measuring..

 [Daekyung Tech] sour gasolin cycle testerQuote Contact_cs @roasexpo.comOxidized gasoline is circulated in the fuel pipe for a certain period of time to check for leaks in the fuel pipe and coupler to determine the product's deformation or pass/fail.CAPACITY : 1.1 Mpa ( 11 kgf / ㎠ )DETECTOR : PRESSURE SENSORMODE : PRESSURE CYCLE, LEAK TES..

[Daekyung Tech] Rupture TesterQuote Contact_cs @roasexpo.comDeformation or pass/fail of a product is judged for the purpose of rupturing the metal or non-metal pipe of a vehicle under high pressure or testing the durability or characteristics up to the target pressure.CAPACITY : (10 ~ 200) Mpa (100 ~ 2000 kgf / ㎠ )DETECTOR : HYD. CYLINDERPRESS..

[Daekyung Tech] Four-way valve testerQuote Contact_cs @roasexpo.comIt automatically controls the valve characteristics and durability leak in the vehicle or home air conditioner to judge product deformation or pass/fail.CAPACITY : 15 Mpa (50 ~ 150 kgf/㎠)DETECTOR : PRESSURE SENSORLOADING : AIR CYLINDERPRESSURE : AIR BOOSTER, CO2 GASCONTROL : P.C CON..

 [Daekyung Tech] Air leak testerQuote Contact_cs @roasexpo.comBy measuring a certain amount of air leakage in the sample (product),the pass/fail of the product is judged. It is easy to use and has the advantage of high reproducibility.CAPACITY : 0.5 Mpa (0~5 kgf / ㎠)DETECTOR : PRESSURE SENSORLOADING : AIR CYLINDERPRESSURE : AIRCONTROL : SEMI-A..

[Daekyung Tech] Hydraulic repeat testerQuote Contact_cs @roasexpo.comRepeatedly apply constant water pressure to metal pipes and clamps to observe crabs or deformations.CAPACITY : 5Mpa (50 kgf / ㎠)DETECTOR : PRESSURE SENSORLOADING : HYDRAULIC CULINDERPRESSURE LIQUID : WATERCONTROL : CONTROLSAMPLE : STEEL PIPE, STEEL CLAMPDEPOSIT : WATER OR AIR..

[Daekyung Tech] Bursting strength testerQuote Contact_cs @roasexpo.comIt is designed and manufactured in digital type as equipment used to measure the breaking strength of various papers,woven fabrics, films, and corrugated cardboard.Input power: AC 220V, 60HzPower consumption: 0.5kWMaximum capacity: 50kgf/㎠Load display: DigitalDevice Size: (600X50..

[Daekyung Tech] Tire CutterQuote Contact_ cs@roasexpo.comThis equipment cuts vehicle tires according to the user's intention.CAPACITY : Ø 510mm X 4.5 tSPEED : 1,700 rpmCONTROL : MANUALLOADING : MOTOR, 3 HpSAMPLE : TIRE..

[Daekyung Tech] Specimen pressQuote Contact_ cs@roasexpo.comWe manufacture rubber and plastic samples of various sizes using inflow.CAPACITY : (100, 200, 300, 500) kNTYPE : HYDRAULIC CYLINDERTEMP : RT, 350 ℃MOLD : ORDER MADEPOWER : 220V, 3PH, (2 ~5) kW..

[Daekyung Tech] Metal specimen model cutting machineQuote Contact_ cs@roasexpo.comThis cutter can cut various metals up to 24mm in diameter.SPIRAL CUTTER : Ø24mmSPEED : (100 ~ 1,800) rpmSAMPLE : AL, STEELJIG : 1 SETPOWER 220V, 1PH, 1kW..

[Daekyung Tech] Mounting pressQuote Contact_ cs@roasexpo.comThis is a newly built DTM-1 mounting press.The temperature difference between the upper and lower parts of the cylinder has been reduced by doubling the heating coil that applies heat.The result is clean, uniform samples.The handle of the cylinder cap has been greatly expanded and designe..

[Daekyung Tech] Medium-sized high-speed cutting machineQuote Contact_ cs@roasexpo.comIt cuts at high speed for quick and simple cutting of medium-sized commercial plates.Sample size: 85 X 85 mm or Ø 95 mmWheel Speed: 300~3600 RPMWheel size: Ø 250 ~ 305 mmSince the lower part is made of a single cast, there is no case of leakage of lubricant and no..

[Daekyung Tech] Medium-to-large high-speed cutting machineQuote Contact_ cs@roasexpo.comIt is manufactured to cut medium-sized specimens precisely and automatically.Cutting size: 160 X 145 or Ø 154Speed ​​(RPM): 1000 ~ 4000 rpmWheel size: Ø 400 mmAuto/Manual : Orderer's specificationIt can be produced with automatic table movement or manual handle..

[Daekyung Tech] High-speed precision cutting machineQuote Contact_ cs@roasexpo.comHigh-speed automatic cutting with a diamond wheel so that medium-sized specimens can be cut precisely.CAPACITY : (60 X 60) mm , Ø 60 mmSPEED : (300 ~ 4,000) rpmWHEEL : DIAMOND WHEELWHEEL DAI : Ø(75 ~ 200) mmLUBRICATLON : PUMPINGCUTTING : MOTOREZEDTYP : AUTOMATIC..

[Daekyung Tech] Low speed precision cutting machineQuote Contact_ cs@roasexpo.comIt is cut at low speed with a diamond wheel so that small specimens can be cut precisely.CAPACITY : (25 X 25) mm, Ø30 mmSPEED : (30 ~ 500) prmWHEEL : DIAMOND WHEELWHEEL DAI : Ø(75 ~ 125) mmLUBRICATION : SELF WETCUTTING : USING DEAD WEIGHTTYPE : MANUALPOWER :..

[Daekyung Tech] Notching molding machineQuote Contact_ cs@roasexpo.comA compact machine capable of making V-notches for plastic impact specimens.V NOTCH CUTTER : Ø75mmSPEED : (40 ~ 80) rpmSAMPLE : PLASTIC IMPACT SAMPLEMOVING : X-Y TABLEPOWER : 220V, 1PH, 1kW..

 [Daekyung Tech] Specimen cutting machineQuote Contact_ cs@roasexpo.comPaper and rubber samples are produced using pneumatic pressure.This is a molding machine that cuts thin samples such as rubber, plastic, paper,and corrugated cardboard in accordance with ASTM, KS, and ISO standards.It uses pneumatics and does not require a separate power s..

 [Dekyung Tech] Paper specimen cutting machineQuote Contact_ cs@roasexpo.comSpecimen maker V capable of cutting specimens for tensile testing and link rush compression..

[Daekyung Tech] Cord creep testerQuote Contact_cs@roasexpo.comIt is an equipment manufactured for the purpose of performing a creep test by inserting a tire cord in the form of a rubber and molded belt for a specified time with a constant load and temperature...