Search

[Daekyung Tech] Pencil hardness testerQuote Contact_cs@roasexpo.comThe tester is easy to operate and is a pencil hardness tester designed to be used to test the thickness and hardness of cutting boards such as paints and films.For the test, apply the lead of a pencil specified in KS G 2603 at an angle of 45 degrees to the drawing,and use it to scra..

[Daekyung Tech] Ring crush compression testerQuote Contact_CS@roasexpo.comThis equipment tests the compressive strength of corrugated cardboard.The test is conducted under the conditions of RCT/ECT/FCT/FAT/CMT/CCT.The maximum load is 5,000 N and the test speed is up to 50 mm/min.Depending on the test method, various pressing jigs are used...

[Daekyung Tech] Motor type bending Wdaring TesterQuote Contact_CS@roasexpo.comIt is manufactured for the purpose of researching and developing the resistance,fatigue recovery, and deformation characteristics of materials by applying fatigue to various materials with the power of the motor...

[Daekyung Tech] Pipe test machineQuote Contact@CS@roasexpo.comIt has been produced for the purpose of reaching the goal by applying the Cracky or Academic Ratio by dividing iron and non-metallic pipes into 8 equal parts...

[Daekyung Tech] Mobile phone wear testerQuote Contact@CS@roasexpo.comThis equipment is a device that measures the lifespan of the contact point when charging the cell phone battery through an endurance test...

[Daekyung Tech] Hydraulic wear testerQuote Contact_CS@roasexpo.comIt is manufactured for the purpose of analyzing, researching,and developing the characteristics of the sample after the durability test is completed by applying torsion after applying a constant load to the thrust bearing.CAPACITY : TORQUE 3 kN.m / FORCE 100kNACCURACY : WITHIN ±1 %CO..

[Daekyung Tech] Real Load Torque Calibrator (100~200) N.mQuote Contact_CS@roasexpo.comThis equipment is used for calibration and testing of electric torque measuring instruments (torque cells).It is a real load torque calibrator with a maximum capacity of 2000 N.m.Equipment supplied to Kia Motors.F2 class weights are used, and clockwise/counterclo..

[Daekyung Tech] Real load torque calibrator 30kN (special specification)Quote Contact_CS@roasexpo.comIt is a device that can calibrate a torque sensor with an actual load.Maximum measuring capacity: 30 kNA variety of weights are applied to accurately measure torque.Used by the Republic of Korea Army.CAPACITY :  (100, 500, 1,000, 2,000)N.mCONTR..

[Daekyung Tech] Real load torque calibrator 100 NMQuote Contact_CS@roasexpo.comIt is a device for correcting torque.The maximum torque is 100 NM, automatically sets the weight, and is designed to measure clockwise/counterclockwise torque.All courses are conducted through Daekyung Tech's dedicated program.The above products are being supplied and us..

[Daekyung Tech] Real load torque calibrator 100 NMQuote Contact_CS@roasexpo.comIt is a device for correcting torque.The maximum torque is 100 NM, automatically sets the weight, and is designed to measure clockwise/counterclockwise torque.All courses are conducted through Daekyung Tech's dedicated program.The above products are being supplied and us..

[Daekyung Tech] Hydraulic force calibratorQuote Contact_CS@roasexpo.comThis equipment is used for calibration and testing of electric force measuring instruments (load cells), and is used to correct the difference between the high-precision master cell,  and the device to be calibrated or to issue a report by the calibration procedure.It is a ..

[Daekyung Tech] Real load force calibrator 10kNQuote Contact_CS@roasexpo.comIt is a standard calibration device that is used for calibration and testing of electric force measuring instruments (load cells), and is calibrated by accurate weight including local gravitational acceleration.It is an instrument for calibrating force measuring instruments..

[Daekyung Tech] Hydraulic force calibratorQuote Contact_CS@roasexpo.comIt is a hydraulic force calibrator with a capacity of 5 MN (approximately 500 tons).It has an uncertainty of 0.05% and is equipped with a two-stage master cell of 5 MN + 2 MN.Tensile/compression bidirectional measurement is possible.It was delivered to VMI in Hanoi, Vietnam, whi..

[Daekyung Tech] Push-pull gauge calibratorQuote Contact_CS@roasexpo.comThis equipment is used for calibration and testing of electric or dial-type push-pull gauges.CAPACITY :  ( 2 ~ 2,000) NCONTROL : MANUALLOADING : DEAD WEIGHTDEAD WEIGHT : STEEL COATING, F2 GRADEMODE : TENSILE , COMPRESSION..

[Daekyung Tech] Hydraulic force calibrator 20kNQuote Contact_CS@roasexpo.comThis equipment is used for calibration and testing of electric force measuring instruments (load cells), and is used to correct the difference between the high-precision master cell,  and the device to be calibrated or to issue a report by the calibration procedure.It ..

[Daekyung Tech] Hydraulic force calibrator 50kNQuote Contact_CS@roasexpo.comThis equipment is used for calibration and testing of electric force measuring instruments (load cells), and is used to correct the difference between the high-precision master cell,  and the device to be calibrated or to issue a report by the calibration procedure.It ..

[Daekyung Tech] Low-temperature impact testerQuote inquiry_ CS@roasexpo.comThis tester is a device that can perform both low-temperature impact and winding tests.It is also used to test the reliability, durability, and lifespan of various samples such as mechanical parts, electrical, electronic, chemical, metal, and ceramics...

[Daekyung Tech] MITQuote Contact_cs @roasexpo.comBy measuring the fluidity in the molten state of the resin, the physical properties (strength, flow chart) and, raw materials of the material are inspected, so defective products can be prevented in advance. is a device for measuring..

[Daekyung Tech] Hydraulic repeat testerQuote Contact_cs @roasexpo.comRepeatedly apply constant water pressure to metal pipes and clamps to observe crabs or deformations.CAPACITY : 5Mpa (50 kgf / ㎠)DETECTOR : PRESSURE SENSORLOADING : HYDRAULIC CULINDERPRESSURE LIQUID : WATERCONTROL : CONTROLSAMPLE : STEEL PIPE, STEEL CLAMPDEPOSIT : WATER OR AIR..

[Daekyung Tech] Metal specimen model cutting machineQuote Contact_ cs@roasexpo.comThis cutter can cut various metals up to 24mm in diameter.SPIRAL CUTTER : Ø24mmSPEED : (100 ~ 1,800) rpmSAMPLE : AL, STEELJIG : 1 SETPOWER 220V, 1PH, 1kW..

[Daekyung Tech] Mounting pressQuote Contact_ cs@roasexpo.comThis is a newly built DTM-1 mounting press.The temperature difference between the upper and lower parts of the cylinder has been reduced by doubling the heating coil that applies heat.The result is clean, uniform samples.The handle of the cylinder cap has been greatly expanded and designe..

[Daekyung Tech] Medium-sized high-speed cutting machineQuote Contact_ cs@roasexpo.comIt cuts at high speed for quick and simple cutting of medium-sized commercial plates.Sample size: 85 X 85 mm or Ø 95 mmWheel Speed: 300~3600 RPMWheel size: Ø 250 ~ 305 mmSince the lower part is made of a single cast, there is no case of leakage of lubricant and no..

[Daekyung Tech] Medium-to-large high-speed cutting machineQuote Contact_ cs@roasexpo.comIt is manufactured to cut medium-sized specimens precisely and automatically.Cutting size: 160 X 145 or Ø 154Speed ​​(RPM): 1000 ~ 4000 rpmWheel size: Ø 400 mmAuto/Manual : Orderer's specificationIt can be produced with automatic table movement or manual handle..

[Daekyung Tech] Low speed precision cutting machineQuote Contact_ cs@roasexpo.comIt is cut at low speed with a diamond wheel so that small specimens can be cut precisely.CAPACITY : (25 X 25) mm, Ø30 mmSPEED : (30 ~ 500) prmWHEEL : DIAMOND WHEELWHEEL DAI : Ø(75 ~ 125) mmLUBRICATION : SELF WETCUTTING : USING DEAD WEIGHTTYPE : MANUALPOWER :..

[Daekyung Tech] Notching molding machineQuote Contact_ cs@roasexpo.comA compact machine capable of making V-notches for plastic impact specimens.V NOTCH CUTTER : Ø75mmSPEED : (40 ~ 80) rpmSAMPLE : PLASTIC IMPACT SAMPLEMOVING : X-Y TABLEPOWER : 220V, 1PH, 1kW..